WORK SURFACE: The work surface will be 11/4” thick 3-ply particleboard construction with .050” high-pressure laminate face and .020” phenolic backer on the underside. The front edge shall be post form laminate or 3mm PVC when specified. The remaining edges shall be square and banded with thin PVC. The work surface shall have one grommet for work surfaces up to 48” long and two grommets for work surfaces greater than 48”. On single-face units, the work surface shall be mounted flush with the leg assembly at the back and sides and flush with the ends on double-face units. The work surface shall be secured by means of 12-gauge clips and 1/4-20 bolts screwed into threaded inserts embedded in the work surface. Laminate choices/options include standard colors from “Wilson Art”, also available from other laminate manufacturers. Additional “premium” laminates are available at an additional cost.

END LEG ASSEMBLY: The leg assembly shall be a double “C” or double “I” shape, constructed of 11 gauge tubular steel and powder coated. The top and bottom rails shall be 2”x3” and the vertical leg rail shall be 2”x4” with an additional 2”x2” square leg rail forming the open trestle. The rails shall be mitered at the joint and welded at the corners on single-faced assemblies and butt-jointed and welded flush on double-faced assemblies. The welds shall be full fillets with all outside welds ground flush. The vertical rails shall have 2”x3” pass-through holes and tapped holes for attachment of raceways on the inside surfaces. The top and bottom rails shall have tapped holes for work surface and accessory attachment and shall be fitted with end caps. The inside rails of the trestle shall be tapped for an optional end panel. The bottom rail shall be fitted with adjustable glides.

INTERMEDIATE LEG ASSEMBLY: The leg assembly shall be a “C” or “I” shape, constructed of 11-gauge tubular steel and powder coated. The top and bottom rails shall be 2”x3” and the vertical leg rail shall be 2”x4”. The rails shall be mitered at the joint and welded at the corners on single-faced assemblies and butt-joined and welded flush at joints on double-faced assemblies. The welds shall be full fillets. The leg rail shall have 2”x3” pass-through holes and tapped for attachment of raceways on both surfaces. The top and bottom rails shall have tapped holes for work surface and accessory attachment and shall be fitted with end caps. The bottom rail shall be fitted with adjustable glides.

CORNER LEG POST: When specified, the leg post shall be constructed of 11-gauge 2”x2” tubular steel. The leg shall be screwed to the work surface with 12-gauge clips and 1/4-20 bolts screwed into threaded inserts embedded in the work surface.

POWER/DATA RACEWAY: The power/data raceway shall be 4” deep x12” high constructed of 18-gauge steel and powder-coated. The raceway shall have a drop-down, removable access door secured by a thumb latch. The raceway shall be capable of being positioned to permit field placement of the access door toward the front or back. The raceway shall be attached to the leg assemblies with 1/4-20 bolts.

SLOTTED END PANEL: When specified, the panels shall be made of 18-gauge steel. Color as specified.

ADJUSTABLE CPU HOLDER: When specified, the adjustable CPU holder shall be steel with adjustable width (5”to 91/2”) and height (15”to 21”). Finish is smooth black. Verify leg & knee space before ordering. Unit includes mounting hardware and foam pads.

CPU HOLDER RACK: The rack CPU holder mounts underneath the work surface at either a right or left side position. The rack CPU holder is expandable and can hold a CPU 61/2” to 10” wide x 18”x21”. The rack unit is slotted on both sides for air ventilation.

REINFORCEMENT KEELS: 60” or 72” nominal length keels are “W” shaped channels made of 14-gauge steel. 60” keels are 31/2” wide x 571/2” long. 72” keels are 31/2” wide x 691/2” long. They attach to the underside of the work surface using wood screws. The purpose of the keel is to prevent the work surface from bowing. RK60s are recommended for use on 60” and 66” wide work surfaces. RK72s are recommended for use on 72” wide work surfaces.

UL LISTING: All standard free-standing, single face, end starter, end adder and center adder models of the Toledo Scholastic Workstation carry UL Listings under File #E301184.